Anti rust method for faucets:

1. Will a layer of dirt or scale accumulate on the faucet in the bathroom that has been used for a long time? If your home is the same, how about giving up using cleaning agents and trying potato peels instead? This can be considered a low-cost "rust removal tool".

2. Take a potato, use a small knife to peel off the potato skin, and then use the meat side to repeatedly wipe the surface of the stainless steel faucet. You will find dirt and scale, and the stains and rust on the faucet will gradually be removed. Then clean the faucet with clean water, and you can see the bright mirror like appearance of the faucet.

4. To prepare salt and vinegar, mix them together, dilute the salt thoroughly in the vinegar, then heat it up. After heating, soak the liquid with a absorbent sponge or cloth, and then place it in a rusty area. Cover for 20-30 minutes.

5. Half an hour has passed. Dip a rough cloth in a mixture of salt and vinegar, and wipe vigorously to easily remove stubborn rust.

6. If using a soft cloth and toothpaste, please pay attention to the degree of force and be careful that the toothpaste will leave small marks on your precious faucet. It is good to use the current crystal toothpaste.

7. If it is chrome plated, it is recommended to clean it with Coca Cola.

8. Coca Cola contains a small amount of phosphoric acid, which reacts with chromium to form a chromium phosphate protective layer. In the 1950s and 1960s, drivers driving cars, motorcycles, and trucks often used cola in industry. Phosphoric acid is still used for these purposes, and all anti rust coatings require phosphoric acid. (Remove water stains)

9. Iron rust requires water and oxygen, and the solubility of gas decreases with increasing temperature. That is to say, in hot water, the solubility of oxygen is relatively small - hot water contains less oxygen and cold water contains more oxygen, so rust occurs faster in the cold one.

Anti rust maintenance of faucets:

1. Although the chrome plating on the faucet claims to be corrosion-resistant and rust free, incorrect cleaning methods can still lead to abnormal wear and tear on the faucet.

2. Experienced and qualified personnel should be hired to carry out construction equipment. When using equipment, the faucet should be kept away from hard objects as much as possible, and cement, glue, and other residues should not be left on the surface to avoid damaging the gloss of the surface coating. Be careful to remove debris from the pipeline before installing the faucet.

3. Easy to use neutral cleaning agents for cleaning, acidic and alkaline cleaning agents are not suitable for faucet cleaning.

4. When the water pressure is not less than 0.02mpa (i.e. 0.2kgf/cm2), if the water output decreases or even the water heater stalls after a period of use, the sieve cover can be quietly unscrewed at the outlet of the faucet to remove impurities, and generally it can be restored to its original state.

5. Don't use too much force to turn on and off the faucet, just quietly roll along with the flow. Even traditional faucets do not require a lot of effort to tighten. Especially, do not use the handle as a handrail to support or use it.

6. Dipping a soft bristled toothbrush in toothpaste or quietly wiping with a scouring pad dipped in toothpaste can remove scale and oil, making the surface of the faucet clean and shiny.

7. Do not use hard objects such as steel wire balls to wipe the surface of the faucet, as steel wire balls are very hard and can easily scratch the surface of the faucet.

8. Many people only pay attention to the surface of the faucet when cleaning it, but in fact, the interior of the faucet is more important. If the water output of the faucet decreases or splits, it may be caused by blockage of the bubbler. You can remove the bubbler, soak it in vinegar, use a small brush or other tools to clean the debris, and then reinstall the equipment.

9. The metal hose of the shower head of the bathtub faucet should be in a stretched condition and should not be coiled around the faucet when not in use. Meanwhile, when in use or not in use, be careful not to form dead corners at the joint between the hose and the valve body to avoid breaking or damaging the hose.

10. After cleaning the faucet, the remaining water on the surface should be wiped dry with a dry, lint free towel to avoid residual water stains.

11. If it is a copper faucet, if you want to clean the electroplated surface, you can use boiling water and detergent to wipe it, or you can directly use some strong degreasing detergent for cleaning.

12. The scale and rust on the faucet only need to be wiped off the surface with a damp cloth or sponge dipped in a small amount of cleaning agent, and then wiped dry with a clean cloth or washed clean with water.

Article source: Kaiping faucet http://www.clasito.net